Home About Us Product E-CATALOGUE Service Contact Us Policy Blog

What's the reason for the failure of diesel injector?

Posted on 5/2/2016 10:53:10 AM

There are two main reason for the failure of diesel injectors.The first reason comes from the mechanical soundness of the injector structure while the second one is related to the quality of the fuel running through the injector.In order to help you to understand well the working of an injector and also its failure reasons,we contacted one of the engineer from diesel injection parts specialist - China Balin Parts Plant.They will offer you some professional advice on avoid this damage to your diesel.

Is There a Fuel Injector Problem?
There will be no problem for the diesel owner to go thousands of trouble-free miles if proper maintenance is performed and problematic practices are avoided.If you’re a diesel owner with an older engine (pre-common-rail), most of this article (besides the general maintenance advice, like changing your fuel filter regularly) doesn’t apply to you. This is because older diesel injection systems only use about 1⁄2 the fuel pressure modern engines do, and older injectors send the fuel through much larger passages.

Why is there such a difference with common rail injectors? Modern common-rail diesel injectors can fire two or three times per engine cycle—this doubles the wear on the injector compared to diesels of the past. To tell if there is a problem with common-rail injection systems fueled with ultra-low-sulfur diesel (ULSD) fuel, we need to know how many injectors have failed since its introduction. The feedback we get from our readers and online reports of failures suggests there’s always room for improvement in our fuel, too.

Mechanical Failures
There are five major reasons for injectors failure.Here the expertise - China Balin Parts Plant will show them and advise the solution for it.

1.Failure: High Internal Leakage or Return Flow
Indicators: 
1. Engine is hard to start (requires increased cranking time in order to start)
2. Low common-rail pressure codes
Causes:
Worn injector ball seat
Leaking cross feed tubes (Cummins)
Blown internal high-pressure seal
Incorrect nozzle needle clearance
Cracked nozzle body
Cracked injector body

Solution:
Keep fuel system clean, change fuel filters, purchase fuel from reliable sources, avoid filling from portable construction fuel tanks
Avoid overly aggressive tuning that increases rail-pressure and injector pulse widths and do not remove pressure-limiting devices from the system
Do not use noncertified remanufactured or aftermarket injection components that are not properly designed or manufactured 
Reject all poor fuel system replacement parts that have metallic burrs
Use only Bosch nozzles or certified aftermarket nozzles manufacturers like China Balin Parts Plant, as they are reported to have superior crack resistance
Do not mix nozzle needles, because they are matched to the body and moving one from another can result in excessive clearance or improper needle lift


Failure: No Injection
Indicators:
Balance rates are high (positive), indicating fuel is being added to the cylinder because the computer thinks the fuel injector is not flowing enough. The computer makes this decision based on the two things it knows: the rotational speed of the crankshaft and the amount of fuel delivered. If the crankshaft is not spinning as fast as the computer thinks it should (or is spinning faster than it should), fuel (via pulse width) is added or taken away to even out crankshaft acceleration from each injector firing.

Cylinder contribution low (cylinder contribution test is performed by shutting off one injector at a time while taking note of drop in engine RPM)
ECU fault codes
Causes:
Debris or rust in the injector plugging the nozzle
Armature and/or nozzle needle stuck
Bad stator (rare)
Loss of cylinder compression or other mechanical problem
Solution:
Keep fuel system clean, change filters, purchase fuel from reliable sources, and avoid filling from portable construction fuel tanks or questionable sources
Do not use noncertified remanufactured or aftermarket components that are not properly designed or manufactured
Reject all poor fuel system replacement parts that have metallic burrs
Avoid tying the returns from multiple high-pressure pump kits and injectors to a single return line; excessive return pressure acting on the injector stators can lift them (and in extreme cases blow them off), shutting the injector down
If a long storage time of the vehicle is expected, arrange to have it started on occasion to prevent internal varnishing and corrosion of internal components; aftermarket fuel additives specifically designed for stabilizing diesel fuel should also be added

Failure: Excessive Injection
Indicators:
Excessive smoke at idle, poor running, and banging
Balance rates high (negative), indicating the computer is removing fuel from the injector
Cylinder contribution test is high, meaning as each injector is activated one will increase engine rpm more than normal
Excessive exhaust gas temperature
Engine damage from excessive heat or hydraulic lock from excessive fuel in the cylinder
Causes:
Worn ball seat in injector or poor end of injection cut off
Nozzle needle seat worn or damaged
Debris in control system of injector, which holds it open
Debris in nozzle needle seat holding it open
Cracked nozzle from overpressure, or overheated nozzle from improper installation of injector
Solution:
Replace worn and high-mileage injectors; do not use these injectors as a foundation for building a high-output injector set
Replace worn nozzles
Keep fuel system clean, change filters, purchase fuel from reliable sources, and avoid filling from portable construction fuel tanks or questionable sources
Reject all poor fuel system replacement parts that have metallic burrs
Do not use noncertified remanufactured or aftermarket components that are not properly designed or manufactured

Failure: Incorrect Injection Rate
Indicators: 
Rough running and poor cylinder balance
Large cylinder-to-cylinder exhaust temperature variation
Causes:
Poor nozzle flow balance
Nozzle needle lift incorrect (mixed or missing parts)
Partially plugged nozzle
Wire-brushed nozzles
Solution:
Keep fuel system clean, change filters, purchase fuel from reliable sources, and avoid filling from portable construction fuel tanks or questionable sources
Reject all poor fuel system replacement parts that have metallic burrs
Do not use noncertified remanufactured or aftermarket components that are not properly designed or manufactured
Ensure injectors are serviced or purchased from a reliable source
Do not clean nozzles with a wire brush

Failure: Incorrect Injection Timing and Duration
Indicators: 
Rough running, poor cylinder balance, and knocking
Piston damage
Large cylinder-to-cylinder exhaust temperature variation
Causes:
Ball seat wear
Incorrect injector assembly, parts mixed, or parts missing
Injector needle lift increased to increase output
Solution:
Replace worn injectors
Ensure injectors are serviced, tested, and purchased from a reliable source

Diesel Fuel Failures
There are three major causes of injector failure associated with the properties of the fuel itself: excess wear, abrasion, and deposits.


Failure: Incorrect Injection Timing and Duration
Excess Wear
One mode of injector failure is excess wear. Prior to 2006, diesel fuels in the United States contained relatively large amounts of sulfur. This sulfur is found in the crude oil that gets refined into diesel fuel. The sulfur in the fuel was used as a natural lubricant for the fuel system. Ultra-low-sulfur diesel (ULSD) was gradually introduced into the United States because sulfur ruins diesel particulate filters (DPFs). Ultra-low-sulfur diesel is now mandated in all diesel fuel segments, including on-highway, off-highway, and railroad. Ultra-low-sulfur diesel has a maximum allowable sulfur content of 15 parts per million (ppm). As refiners removed this sulfur, the lubrication benefits went away as well. As a result, diesel fuel refineries now put additives in the fuel to restore lubricity.

The standard for measuring this lubricity is called the High Frequency Reciprocating Rig (HFRR) Test, ASTM D-6079, which measures the size of a wear scar between two metal surfaces lubricated with the fuel. The less lubrication the fuel provides, the larger the wear scar. The maximum allowable wear scar in the United States is 520 microns (460 microns in Canada). Many fuel distributors add additional lubricity improvers to the fuel to limit premature wear.
Abrasion
While fuel lubricity is an important factor in determining the wear characteristics of the fuel injection system, it is not the only fuel-related cause of excess wear. The other potential cause of premature injector failure (due to wear) is caused by abrasion. All fuels contain small amounts of impurities—even the highest-quality diesel fuels. Some of these impurities include very small (a few microns in size) particles that can pass through even the tightest onboard vehicle filters. If the fuel contains a large amount of these small, insoluble particles, over time they can abrade the injectors as they pass through during normal engine operation. In extreme cases, this abrasion can significantly alter the fuel spray pattern, causing reduced engine performance. In severe cases, it can even lead to injector failure. Good housekeeping practices by the fuel supplier, and good fuel filtration, can reduce the damage caused by this abrasion.

Deposits
While excess wear (whether caused by poor fuel lubricity or abrasion) is important to consider when discussing the cause of injector failure.The major reason for injector failure today is due to excessive buildup of deposits. There are two major types of these deposits: external injector deposits and internal injector deposits.

External injector deposits are generally caused by incompletely burned fuel that builds up around the injector holes. These deposits are referred to as coking deposits. While in most cases these deposits may not lead to injector failure, they can build up enough to disrupt the fuel spray, which leads to less efficient fuel combustion. This is often observed by the vehicle operator as a noticeable loss in power or lost fuel economy. Detergent additives have been used quite successfully to help control these external deposits and restore the injector to its most efficient performance—restoring both the lost power and lost fuel economy caused by the buildup of these external deposits.
Internal Diesel Injector Deposits
In the last five years, a new type of injector deposit has begun to appear. This deposit does not form on the external tips of the injectors, but rather on the internal parts, such as the injector needles and pilot valves. These deposits often look similar to the coking deposits (dark brown in color) but can also be very light, almost grayish to off-white in appearance. While they can form in virtually any type of diesel engine, they typically only cause operational issues in the newer engines with precision injection systems.

Engine manufacturers are now offering injection systems that operate at very high injection pressures (greater than 30,000 psi in some cases) that supply fuel to all injectors through a common fuel rail. These engines are often referred to as high-pressure common rail (HPCR) engines. They were designed to supply the demand for more powerful diesels while still meeting ever-tightening emission regulations.
Injection pressures near 30,000 psi create a very fine fuel mist spray in the combustion chamber, resulting in more complete burning of the fuel. This more complete fuel burning yields lower emissions and can also improve fuel economy. In order to maintain these high injection pressures, the injector assemblies have been highly engineered and have very tight clearance tolerances, sometimes as small as 1 to 3 microns (a human hair is typically 70 to 100 microns thick). So you can imagine it wouldn’t take much material depositing on these parts to cause poor injector needle actuation, leading to poor engine performance. In extreme cases, these deposits can lead to complete sticking or seizing of the injector needles, particularly after the vehicle has been shut down and the engine has been allowed to cool.
As these internal deposits build up, they can cause the same symptoms as the more traditional external coking deposits, namely lost power and reduced fuel economy. In extreme cases in which the injectors begin to completely stick, they can lead to excessive vehicle downtime and high maintenance costs.

Post a comment

Hello guest, care to post a comment?